As we all know, the kitchen and the bathroom are the most used places in the whole family. At this time, we need to use the floor drain. The floor drain refers to the drainage device connected to the drainage pipe system. It is an important interface between the drainage pipe system and the indoor floor. The important components of the drainage system in the house, its performance directly affects the quality of the indoor air, and is very important for the control of the odor of the bathroom.

Although the floor drain only takes up a small position in the home, it is critical. There are problems with the selection and installation of floor drains, and the home is prone to flooding, and it gives off an unpleasant smell at any time, which greatly changes the home life. So how to install the floor drain? What are the precautions for the floor drain installation? Next, the small series will introduce it to everyone.

The floor drain installation university asked: the details can not be underestimated!

[How to install the floor drain]

1, check the drain

Before installing the floor drain, it is necessary to check whether the drain pipe is blocked or not. Before installing the floor drain, it is necessary to protect the drain port so as not to block the pipe by foreign matter.

2, install a fixed floor drain

The floor drain installation is generally carried out simultaneously with the floor tile paving. Select the corresponding floor drain, apply a layer of cement on the reverse side of the floor drain panel, then align the drain, cover the floor drain panel, and fix it. I suggest that you must not overlook this point, and lay the foundation is the most critical.

3, kitchen and bathroom floor drain installation attention slope treatment

The kitchen and toilet must pay attention to the slope when installing the floor drain. "The flow of water to the lower part" believes that everyone understands that the kitchen and the water are the same. When paving, you need to make a certain slope around the floor drain so that the water can flow naturally down.

4, floor drain installation acceptance

After the floor drain is fixed and sealed with glass glue or adhesive, the floor drain is checked and accepted. Check the drainage capacity by draining water to the ground, check the slope of the floor drain to check the slope rationality, and try to remove the sealing core to see if it is supported by cement.

[floor drain installation precautions]

1. The floor drain core must be taken out before the floor drain is installed. This can prevent debris from falling into the drain core and causing damage.

2, the purpose of installing the floor drain is to drain, so the location of the floor drain installation is slightly lower than the ground, convenient for drainage. Before the floor drain is installed, if the drain pipe is too close to the ground, the drain pipe should be cut to the right amount to ensure that the installed floor drain panel is slightly lower than the ground.

3, in order to ensure that the overall decoration effect is not destroyed, the location of the floor drain installation can not be too much lower than the ground, so if the drain pipe is too far from the ground, use cement mortar to fill, so that the purpose of raising the drain pipe can be achieved, the floor drain After installation, the perfect decoration effect can be guaranteed.

4. When installing the floor drain, in order to prevent the tools and Other items from falling into the drain pipe and causing blockage, block the drain pipe with cloth or other soft objects beforehand, and take it out when installing the drain core.

5, floor drain installation should take into account the future maintenance is convenient, so when filling the cement mortar, can not directly use the floor drain, but use kraft paper or other strong material to roll into a cylinder matching the downpipe, docking with the downpipe, and Above the ground, then fill the cement mortar.

6. The floor drain is docked with the lower water pipe and raised above the ground. Fill the surrounding cement gap with the stirred cement mortar (1:1), adjust the height of the floor drain panel to a suitable position, and place the floor drain after the cement mortar is solidified. It forms a pipe that fits snugly against the pipe wall.

7. If the floor drain is used in the washing machine, you can purchase a special washing machine floor drain or connecting piece. Of course, you can also use the ordinary floor drain directly. Just plug the drain tube into the fixed pin on the top of the floor drain, but it is practical. And convenience is not as good as the first two.

Heavy Hex Nuts

Heavy Hex Coupling Nut ,Heavy Hex Jam Nut ,Heavy Hex Nut Grade,Heavy Hex Nut

Kunshan Zhonggu Precision Hardware Co., Ltd. , https://www.zgfastener.com