In recent years, people pay more and more attention to sanitary ware bathroom, not only the decoration is better, the choice of sanitary ware has become very careful, coupled with this special space of the bathroom, sanitary ware bathroom installation is also very important, which to a large extent Concerned about future use. Then, the next small series for everyone to introduce sanitary ware bathroom installation.

Sanitary ware installation

1, the installation of the bathtub

The first step is to test the water to see if it is leaking: Before we put the bathtub, we need to properly install the water fittings, and we need to close the water for 24 hours, and then look at the leaking condition of the bathtub. In particular, pay attention to the overflow.

The second step is to level the bathtub: When we set up the bathtub, we must pay attention to the corresponding water outlet is lower than the end of the inlet, which will avoid the poor sewage. Corresponding bathtubs must not only be visually level, but also care must not affect drainage.

The third step is to fill in the sand: Compared with the cast iron bathtub, it is strong but its thermal conductivity is very fast. Therefore, it is necessary to use Mid River Sand for compaction. Of course, foam can also be used because the foam does not have liquidity. When filling river sand, it is also necessary to note that sand cannot leak into the sewers.

The fourth step is to leave the access port: We also need to pay attention to the holes 300mm wide and 400mm high at the place where the water outlet is installed, and perform the waterproof and anticorrosive treatment according to the size. The purpose of this is to have a good mouth when we are doing maintenance.

2, toilet installation

In the first step, we need to remove the pipe plug from the ground, and then we need to check if there is any debris in the pipe. If necessary, we need to remove the corresponding debris. Then clean the area around the nozzle, and then connect the corresponding outlet pipe of the toilet with the outlet pipe to make it flat and correct. Then we need to mark the bolt holes in the toilet bowl.

The second step is to make holes. A hole with a diameter of 20 mm and a depth of 60 mm should be drilled at the corresponding mark. Then insert the bolt into the hole, then cement it firmly and align the toilet eye with the bolt. Then put the putty around the corresponding outlet of the toilet bowl and the outlet nozzle, and screw the corresponding four bolt holes of the toilet until the elasticity is moderate.

The third step is to install the rear center of the toilet bowl. According to the corresponding drawings or the scribed section for installation, and the relevant bolts need to be fixed, the degree of fixing needs to be moderate, not too tight.

The fourth step is to install the backwater tank. When installing the back tank, we need to pay attention to the proper size, not too loose or too tight.

The fifth step is connected to the water. The installation of the Sheung Shui system also needs attention, and it cannot leak water. When you finish the water, you need to pay attention to moderate elasticity.

3, washbasin installation

The first step is to install the washbasin: When we are installing the washbasin, we must first draw the line of the discharge pipe, and then measure the height of the floor upwards, and draw a horizontal line on the wall. Mark the mark according to the width of the basin, then make a 120 mm deep hole. Clean up the related debris and keep it clean.

The second step is the installation of the cast iron washbasin. As with the above installation method, it is also necessary to mark the center of the discharge nozzle, then measure the height, and draw horizontal lines to form a crosshair. Depending on the width of the washbasin, mark it on the centerline, and place the pots in place, leaving the screw holes in place, and the size must be marked.

Sanitary ware bathroom cleaning method

1, ceramic basin cleaning

Porcelain basins in the bathroom are the easiest proof of whether your bathroom is clean or not. After using it for a long time, rust stains will appear on the metal and ceramic of the pelvic floor. Put the appropriate amount of salt in the same amount of vinegar, stir it with heat, and then rub it on a soft cloth. Salt vinegar solution on the rust spot for half an hour, you can choose to scrub the rough fabric.

2, bathroom deodorant

Put the lemon peel or soaked dry tea in the bathroom and the odor will soon disappear. If the odor is emitted from the toilet, a match can be ignited and dropped into the toilet. The odor will be quickly eliminated.

3, the bathroom mold

Because the bathroom is wet, it is the most prone to mildew. To prevent bacterial growth, first clean thoroughly. If it grows, use bleach to remove it. Use a cotton swab to dip a hundred times the diluted bleach to apply to the moldy area. After half an hour, brush it off with a toothbrush and the tile will be able to restore its original whiteness and lightness.

4, bathtub cleaning

Bathrooms are also prone to dirt because they often have water, stubborn dirt can be used to wet the coup with bleach; the toilet paper is soaked in bleach diluted ten times, and then deposited on the stubborn bath or tile. After a period of time, remove the wet toilet paper and gently clean the pasted area with water to easily remove stubborn dirt.

5, shower cleaning

Washing baths found that the amount of water is less, may not be the problem of water pressure, in fact, is the problem of shower nozzles. After showering in the evening, pour half a glass of vinegar in the washbasin and put some water on it. Then remove the shower head and soak it in vinegar. The next morning, the shower head will be completely clean and the water will flow smoothly.

6, mirror wipe

Apply some soap on the mirror, then wipe it with a dry cloth to form a protective film that can insulate the steam. If you have unwanted perfume, it is better to use it to wipe the mirror. Put a few boxes of cool oil in the ventilated room in the bathroom, you can smell bursts of fragrance, but also to keep the bathroom dry.

Editor's summary: The installation of sanitary ware is introduced here, and we hope to help everyone. If you want to know more related information, you can pay attention to this website information.

Sanitary Ware Sanitary Ware Sanitary Ware Bathroom Floor Drain Sanitary Ware Installation Sanitary Installation

Pvc Hollow Sheet has good sound insulation effect: PVC Hollow Sheet can absorb noise or reduce noise passing through when it is affected by external noise such as rainstorm, hail, gale and so on.
Tough texture and high strength: another basic feature of PVC hollow sheet roof is that it must be able to withstand unexpected impact and cannot be damaged by natural external forces.
Volume stability: the PVC hollow sheet has low expansion coefficient and tensile property, which ensures that the geometric size of the tile remains unchanged even if the temperature changes greatly.

PVC Hollow Sheet

Plastic Roofing,Pvc Hollow Sheet,Pvc Hollow Tile,Corrugated Roof Panels

PINGYUN INTERNATIONAL , https://www.pingyunconstruction.com